Fire Alarm Systems

Fire alarm is a system that is built with the aim of detecting symptoms of fire in a building, especially for multi-storey buildings and neutral buildings.

So, with a fire alarm in a building, of course, it will make it easier for the building security team to quickly find out the specific fire area. So, the evacuation and extinguishing process can be done quickly.

  • One Class A or Class B intelligent device loop standard, optional loops brings control panel capacity to 1000 devices

• 24-line by 40-character backlit LCD capable of displaying eight simultaneous events

• Optional voice evacuation and firefighter’s telephone

• Part of an end-to-end audio solution suitable for low frequency signaling in sleeping areas

• Optional network interface slots are located on the back of a swingable mounting chassis

• Electronic addressing with automatic device mapping

• Optional Ethernet port for diagnostics, programming

• Supports strobe synchronization

• Supports up to 30 R-Series remote annunciators with either Class A or Class B wiring

• Networkable up to twenty four VM control panels monitoring 24,000 intelligent points

• Patented Voltage Boost™ technology delivers constant voltage on NAC and AUX circuits — even at low battery power.

• 10 Amp UL listed power supply with universal 94 to 264 Vac input voltage

• Integrated Carbon Monoxide gas sensing with V-PCOS detectors including distinct audible signaling

• Four on-board Notification Appliance Circuits

• Room for three optional front panel LED/Switch modules

• Optional Ethernet interface

• UL2572; UL864 UUKL; UL 864 Listed for releasing applications using GSA-REL • Optional earthquake hardening: seismic Importance Factor 1.5

• Next generation detection technology

• Integrates optical smoke with carbon monoxide detection

• Wide 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) smoke obscuration

• Sensor Markings Provide Easy Testing Identification

• Uses existing wiring

• Automatic device mapping

• Ground fault detection by module

• Up To 250 Total Addresses Per Loop

• Two levels of environmental compensation

• Two levels of dirty detector warning

• Up to twenty pre-alarm settings

• Five sensitivity settings

• Non-volatile memory

• Electronic addressing

• Environmental compensation

• Automatic day/night sensitivity adjustment

• Bicolor (green/red) status LED • Standard, relay, fault isolator, and audible mounting bases

• Vibrating and single stroke

• 6 inch (150mm), 8 inch (200mm), 10 inch (250mm) sizes

• Red or gray finish

• Rugged compact mechanism

• Heavy duty cast housing

• Low power drain

• Wide voltage selection

• Indoor or weatherproof

  • Unique low-profile design
  • The most compact UL-1971/ULC-S526 listed strobe available
  • Ultra-slim – protrudes less than one inch
  • Attractive appearance
  • No visible mounting screws
  • Select 15, 30, 75, or 110 cd strobe output
  • Select high (default) or low dB horn output
  • Select temporal (default) or steady horn output
  • Select public mode flash rate (default) or private mode temporal flash
  • Fixed 15/75 cd model available
  • ECS/MNS models available
  • Easy to install
  • Fits standard 1-gang electrical boxes – no trim plate needed
  • Optional trim plate accommodates oversized openings
  • Pre-assembled with captive hardware
  • #12 AWG terminals – ideal for long runs or existing wiring
  • Unparalleled performance
  • Industry’s most even light distribution
  • Meets tough synchronizing standards for strobes
  • Single microprocessor controls both horn and strobe
  • Independent horn control over a single pair of wires
  • Highly regulated in-rush current
  • Multiple frequency tone improves sound penetration
  • Field-programmable temporal strobe output option
  • Pull lever
  • Simple positive operation
  • Break glass
  • Attractive, streamline design
  • Less than 5 lb pull force complies with ADA
  • Solid, die-cast metal construction
en_USEnglish